CONNFLY DS1026-01-1*14S8BV Female Header, 1×14, 2.00 mm, THT, 2 A

CONNFLY DS1026-01-1*14S8BV Female Header, 1×14, 2.00 mm, THT, 2 A

CONNFLY DS1026-01-1*14S8BV is a single-row 14-position female header designed for vertical through-hole mounting on a printed circuit board. It features a 2.00 mm contact pitch, gold-plated contacts and a compact 4.3 mm profile height. The connector is intended for electronic boards, modules and other assemblies requiring a detachable 1×14 socket connection with a 2.00 mm pitch.

Key parameters:
1×14 contacts • 2.00 mm pitch • vertical THT • 2 A • gold-plated contacts • −40…+105 °C

Key features

• 1×14 contact arrangement – fourteen socket contacts in a single row provide a compact connection for signal or power lines on a PCB.
• 2.00 mm contact pitch – smaller than the common 2.54 mm pitch, allowing use in more compact electronic assemblies.
• Vertical THT mounting – 2.7 mm PCB leads are intended for soldering into plated or non-plated through-holes with the connector perpendicular to the PCB.
• 2 A current rating – the manufacturer specifies a current rating of 2 A.
• Gold-plated contacts – copper-alloy contacts are nickel underplated and finished with a thin gold layer specified as “Full gold flash”.
• Low contact resistance – maximum contact resistance specified by the manufacturer is 20 mΩ.
• Wide operating temperature range – specified for operation from −40 °C to +105 °C.
• UL94 V-0 insulator rating – the black high-temperature insulator is specified by the manufacturer as UL94 V-0.

Applications

The connector is intended for printed circuit boards, control modules, interface boards, prototypes and other electronic assemblies requiring a single-row 14-position female header.

Its THT construction is designed for soldering into PCB holes. The vertical orientation allows the mating connector to be inserted perpendicular to the PCB surface.

Compatibility and limitations

The connector uses a 1×14 layout with a 2.00 mm pitch. When selecting a mating male header, both the 2.00 mm pitch and the mechanical contact dimensions must be checked, as the manufacturer's datasheet does not specify a particular mating CONNFLY part number.

This is a THT connector and not an SMT connector.

The specified 500 V AC(rms) for 1 minute is a dielectric withstand test value. It must not be interpreted as the rated or maximum operating voltage because no operating voltage is specified in the manufacturer's datasheet.

Technical specifications

Parameter	Value
Manufacturer	CONNFLY
Model	DS1026-01-1*14S8BV
Connector type	Female Header / socket strip
Contact type	Socket, female
Number of contacts	14
Contact arrangement	1×14
Contact pitch	2.00 mm
Mounting	Vertical THT / V/T
Current rating	2 A
Contact resistance	≤20 mΩ
Insulation resistance	≥1000 MΩ
Dielectric withstand test	500 V AC(rms), 1 min
Operating temperature	−40…+105 °C
Contact material	Copper alloy
Contact plating	Gold over nickel, “Full gold flash”
Insulator	High-temperature type, black
Insulator flammability rating	UL94 V-0
Body length	28.5 ±0.3 mm
Body width	2.40 mm
Body height	4.30 mm
PCB lead length	2.70 mm
Lead cross-section	0.50 × 0.20 mm
Centre distance between outer contacts	26.0 mm nominal
Recommended PCB hole diameter	Ø0.80 mm
Recommended PCB pitch	2.00 mm
Housing colour	Black

Construction and mounting

The connector has a single-row, low-profile 4.3 mm body. Fourteen female contacts are arranged at a 2.00 mm pitch, with 2.7 mm leads intended for through-hole soldering.

The manufacturer's recommended PCB layout uses Ø0.80 mm holes positioned at a 2.00 mm pitch.

Important use and safety notes

• Check the manufacturer's mechanical drawing and recommended PCB layout before designing the PCB footprint.
• The 500 V AC(rms) / 1 min value specifies dielectric withstand testing and is not an operating-voltage rating.
• Circuit design should observe the manufacturer's 2 A current rating and take actual operating and temperature conditions into account.
• Mechanical compatibility of the mating connector should be verified from its contact geometry rather than from the 2.00 mm pitch alone.